|













| |
|
TRANSMITTERS
& DISPLAYS WITH INDIVIDUAL A/D'S
(MA/VDC or DIGITAL Outputs, PLC Interfaces)
Eliminate
summing junction boxes, 4 individual A/D inputs.
4 times
more sensitivity over conventional summing box averaged
signals.
No pot
adjustments, electronic calibration to data sheet
specifications.
Individual cell diagnostics and fault detection, alarm on system
errors.
Bypass cells, automatic recalibration to compensate for
defective cells. |
|
DGT- Digital
Weight Transmitter DIN Rail Mount
Single scale up to 4
load cells individually monitored, eliminates summing box.
or 4 separate scales
with maximum of 16 load cells at 350 Ohms
24-bit
sigma-delta A/D conversion, up to 200 conv./sec. auto-select
12 to 24 VDC power, 5
function keypad, 2 inputs, 2 outputs,
Analog output or
ProfiBus interface, serial ports.
Front panel or PC
program set up.
Send mail to
info@iwsystems.ca
for additional information
|
|
|
DGTQ-
Digital Weight Transmitter Panel Mount
Single scale up to 4
load cells individually monitored, or 4 separate scales.
24-bit
sigma-delta A/D conversion, up to 200 conv./sec. auto-select
12 to 24 VDC power, 5
function waterproof keypad, 2 inputs, 2 outputs,
Analog output or
ProfiBus interface, serial ports.
Front panel or PC
program set up.
Send mail to
info@iwsystems.ca
for additional information
|
|
|
DGTP-
Digital Weight Transmitter Panel Mount
Single scale up to 4
load cells individually monitored, or 4 separate scales.
24-bit
sigma-delta A/D conversion, up to 200 conv./sec. auto-select
12 to 24 VDC power, 5
function waterproof keypad, 4 inputs, 6 outputs,
Analog output or
ProfiBus interface, serial ports.
Front panel or PC
program set up.
Send mail to
info@iwsystems.ca
for additional information
|
|
|
DGT20-
Digital Weight Transmitter Bench / Wall Mount
Single scale up to 4
load cells individually monitored, or 4 separate scales.
24-bit
sigma-delta A/D conversion, up to 200 conv./sec. auto-select
12 to 24 VDC power, 5
function waterproof keypad, 2 inputs, 2 outputs,
Analog output or
ProfiBus interface, serial ports.
Front panel or PC
program set up.
Send mail to
info@iwsystems.ca
for additional information
|
|
|
DGTPK-
Digital Weight Transmitter Bench / Wall Mount
Single scale up to 4
load cells individually monitored, or 4 separate scales.
24-bit
sigma-delta A/D conversion, up to 200 conv./sec. auto-select
12 to 24 VDC power, 5
function waterproof keypad, 4 inputs, 6 outputs.
Serial ports, Front
panel or PC program set up.
Send mail to
info@iwsystems.ca
for additional information
|
|
|
UWT-I-Box
2000
Load cells connect to I-Box 2000 with 4 individual A/D
converters.
UWT Display is 24 VDC powered and digitally communicates
to the I-Box
Display each load cell (%load, Mv/V, Weight) easy programming
menu's.
Analog output on total of all cells or PLC interfaces are
available.
|
|
|
E-Link
3000 Direct
PLC interface from load cells.
Free PC programming software to RS-232 Port-1or via PLC master
protocol port 2.
DeviceNet, ProfiBus, CANOPEN, Modbus TCP ,
Modbus RTU.
Standard DIN rail
mounting, shown with optional fiberglass NEMA-4 enclosure.
|
|
iQUBE2 Digital
Diagnostic Junction Box
Each card
can be up to four separate platforms/cells + total, or
four separate scales Diagnostic routines for weighing errors and system
health.
Tests for
zero return, linearity, and drift Cell Emulator compensates for load cell failure until a
repair can be made Cal-Match algorithm automatically trims and calibrates
the scale in one pass.
Standard
communication RS-232.
Option card
slot for Fiber Optic, Ethernet TCP/ IP or Wireless TPC/IP,
or RS-485 Four digital I/O per card, for push button operation,
control, or remote cell status
|
|
|